Print Page

Font Size:
Product

Product Features

Specifications

General specifications

ItemSpecifications
Operating ambient temperature *10 to 50 ℃
Storage ambient temperature-20 to 60 ℃
Operating/Storage ambient humidity10 to 90% RH, non-condensing *2 (The wet bulb temperature is 39℃).
Vibration resistanceConforms to
IEC 61131-2
 FrequencyAccelerationHalf-amplitudeSweep Count
Under intermittent vibration5 to 8.4 Hz-3.5 mm10 times each
in X, Y and Z
directions
8.4 to 150 Hz9.8 m/s²-
Under continuous vibration5 to 8.4 Hz-1.75 mm-
8.4 to 150 Hz4.9 m/s²-
Shock resistanceConforms to IEC 61131-2 (147m/s², 3 times each in the X, Y, and Z directions)
Operating atmosphereMust be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles. Must be no direct sunlight. (Same as for saving)
Operating altitude *32000m (6562ft) max.
Installation locationInside control panel
Overvoltage category *4Ⅱ or less
Pollution degree *52 or less
Cooling methodSelf-cooling
GroundingGrounding with a ground resistance of 100 Ω or less by using a ground cable that has a cross-sectional area of 0.14 to 1.5 mm2 (solid wire), 0.14 to 1.0 mm2 (stranded wire), or 0.25 to 0.5 mm2 (rod terminal with an insulation sleeve). If impossible, connect the ground cable to the control panel.
  • *1 Includes the temperature inside the enclosure of the control panel to which the GOT is installed.
  • *2 If the ambient temperature exceeds 40 °C, the absolute humidity must not exceed 90% RH at 40 °C.
  • *3 Do not use or store the GOT under pressures higher than the atmospheric pressure of altitude 0 m (0 ft).
    Failure to observe this instruction may cause a malfunction. When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press, and the sheet may be peeled off.
  • *4 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the machinery within the premises.
    Category II applies to equipment for which electrical power is supplied from fixed facilities. The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
  • *5 This index indicates the degree to which conductive pollution is generated in the environment where the equipment is used.
    In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.

Power supply specifications

ItemSpecifications
GS2110-WTBDGS2107-WTBD
Input power supply voltage24 V DC (+10%, -15%), ripple voltage 200 mV or less
Power consumption 7.6 W (317 mA/24 V) or less6.5 W (271 mA/24 V) or less
 At backlight off3.8 W (158 mA/24 V) or less3.8 W (158 mA/24 V) or less
Inrush current17 A or less (6 ms, ambient temperature 25 ℃, at the maximum load)
Permissible instantaneous power failure timeWithin 5 ms
Noise immunityConforms to IEC61000-4-4, 2 kV (power supply line)
Dielectric withstand voltage350 V AC for 1 minute (across power supply terminals and earth)
Insulation resistance500 V DC across power terminals and earth, 10 MΩ or more by an insulation resistance tester

Performance specifications

ItemSpecifications
GS2110-WTBDGS2107-WTBD
Display section *1TypeTFT color liquid crystal display
Screen size10"7"
Resolution800 × 480 dots
Display sizeW222 (8.74) × H132.5 (5.22) [mm] (inch) (Horizontal format)W154 (6.06) × H85.9 (3.38) [mm] (inch) (Horizontal format)
Display character16-dot standard font: 50 characters 30 lines (Horizontal format)
Display color65536 colors
Brightness32-level adjustment
BacklightLED-type (no replacement required)
Backlight off/screen saving time can be set.
Touch panel *2TypeAnalog-resistive film type
Key sizeMinimum 2 × 2 [dots] (per key)
Number of points touched simultaneouslySimultaneous 2-point presses prohibited (Only one point can be touched.)
Life1 million times (operating force 0.98 N max.)
MemoryC driveFlash memory (Internal) (9 MB), for storing project data, OS
Life (Number of write times) 100000 times
Built-in interfaceRS-4221 ch
Transmission speed: 115200/57600/38400/19200/9600/4800 bps
Connector shape: D-sub 9 pins (Female)
Terminating resistor: 330 Ω fixed
RS-2321 ch
Transmission speed: 115200/57600/38400/19200/9600/4800 bps
Connector shape: D-sub 9 pins (Male)
Ethernet1 ch
Data Transfer method: 100BASE-TX, 10BASE-T,
Connector shape: RJ-45 (modular jack)
USB (device)1 ch (rear face)
USB version: USB 1.1 (Full-Speed 12 Mbps)
Connector shape: USB Mini-B
SD memory card1 ch
Conforms to the SD standard,
Supported memory card: SDHC memory card, SD memory card
Buzzer outputSingle tone (LONG/SHORT/OFF adjustable)
Protective structure *3IP65F (only the front part of the panel)
External dimensionsW272 (10.71) × H214 (8.43) × D56 (2.21) [mm] (inch)W206 (8.11) × H155 (6.11) × D50 (1.97) [mm] (inch)
WeightApprox. 1.3 kg (Excluding mounting fixtures)Approx. 0.9 kg (Excluding mounting fixtures)
Compatible software packageVersion1.215Z or later *4
  • *1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel. It is impossible to completely avoid this symptom, as the liquid crystal display comprises of a great number of display elements. Flickers and partial discoloration may be generated on the liquid crystal display panel due to individual differences of panels. Please note that these phenomena appear due to its characteristic and are not caused by product defect.
  • *2 The touch panel is an analog-resistive type. Simultaneous pressing of two or more areas on the touch panel may activate the switch between those areas. Do not press two or more areas simultaneously on the touch panel.
  • *3 Note that this does not guarantee all users' operation environment. In addition, the product may not be used in environments under exposition of oil or chemicals for a long period of time, or in environments filled with oil-mist.
  • *4 When the software is earlier than GT Works3 Version1.215Z, installation of the GS installer is required.

External dimensions

GS2110-WTBD

gs2110wtbd[Unit: mm (inch)]

GS2107-WTBD

gs2107wtbd[Unit: mm (inch)]

Components names

GS2110-WTBD

gs2110wtbd

GS2107-WTBD

gs2107wtbd
  • 1) Display section
  • 2) Touch panel
  • 3) RS-232 interface
  • 4) RS-422 interface
  • 5) Ethernet interface
  • 6) USB interface (device)
  • 7) Cable clamp mounting hole
  • 8) Rating plate
  • 9) SD memory card interface
  • 10) SD memory card access LED
  • 11) Power terminal
  • 12) Ethernet communication status LED
  • 13) Unit installation fitting

Panel cutting dimensions

Panel cutting dimensions

Panel thickness: 1.6 to 4 mm (0.06 to 0.15 inch)

Horizontal format (If the vertical format is selected, the dimension must be rotated 90°.)

Cut holes in the following dimensions on the panel.
Ensure 10 mm of space in upper and lower parts of the panel for mounting fixtures.

[Unit: mm (inch)]

ModelAB
GS2110-WTBD258 (10.16")200 (7.88")
GS2107-WTBD191 (7.52")137 (5.4")

Subscribe
Receive the latest headlines, right to your inbox